How long is this power lead?
The cable is 5 metres long, providing considerably more reach than a typical short equipment power lead.
18 products
18 products
Sort by:
£4.95
Unit price per£4.95
Unit price perThis 5m black UK power lead provides a straightforward replacement or extended-length mains connection for compatible electrical equipment fitted with an IEC C14 power inlet.
Commonly referred to as a kettle lead, IEC lead or computer-style power lead, the cable connects a standard UK 3-pin mains socket to a compatible IEC C14 appliance inlet using an IEC C13 female connector.
The generous 5 metre cable length provides considerably more flexibility than a standard short equipment lead, making it useful where electrical equipment needs to be positioned further away from the available mains socket.
It is particularly useful as a replacement for lost or damaged power cables on compatible ballasts, controllers, environmental equipment and other electrical devices that use a standard IEC C14 inlet.
Why choose the 5m UK IEC power lead?
UK plug to IEC C13 connection
The equipment end of this cable uses the familiar IEC C13 female connector. This connects to a matching IEC C14 male inlet fitted to the electrical equipment.
IEC C13/C14 connections are commonly found on computers, monitors, controllers, power supplies and many other electrical devices. They are also used by compatible lighting ballasts and horticultural equipment.
Before ordering, check the inlet on your equipment. A standard IEC C13 connector has a different profile from other IEC connectors such as C15 and C19, so physical compatibility should always be confirmed rather than relying on the general term "kettle lead".
5 metre cable for flexible equipment positioning
The extended 5m length is particularly useful in larger installations where equipment positioning is dictated by ventilation, lighting, irrigation or working-space requirements rather than the position of the nearest mains socket.
Additional cable length can help achieve a cleaner installation without placing unnecessary tension on the plug or equipment connector.
Route the cable carefully and avoid creating trip hazards, crushing the cable beneath equipment or running it across sharp edges. Any excess cable should be managed neatly without placing strain on either connector.
Replacement power lead for compatible equipment
Detachable IEC power cables are convenient because a damaged or misplaced lead can often be replaced without replacing the equipment itself.
This 5m lead can be used as a replacement where the equipment requires a UK mains plug to IEC C13 connection.
Always check the equipment manufacturer's electrical requirements and connector type before use. The physical connector fitting correctly does not by itself confirm that a cable is suitable for every appliance or electrical load.
Using an IEC power lead safely
Electrical power leads should be inspected periodically, particularly in busy working environments where cables may be moved, disconnected or routed around other equipment.
5m UK Power Lead product details
| Product type | UK mains power lead |
|---|---|
| Cable length | 5m |
| Colour | Black |
| Mains connection | UK 3-pin plug |
| Equipment connection | IEC C13 female connector |
| Compatible equipment inlet | IEC C14 |
| Common description | Kettle lead / IEC power lead |
| Typical use | Replacement or extended-length mains connection for compatible electrical equipment |
| Outer case quantity | 25 leads |
5m UK IEC Power Lead FAQs
How long is this power lead?
The cable is 5 metres long, providing considerably more reach than a typical short equipment power lead. What connector is on the equipment end?
The equipment end uses an IEC C13 female connector, designed to connect to a compatible IEC C14 appliance inlet. Is this a UK power lead?
Yes. The mains end is fitted with a UK 3-pin plug. Is this what people call a kettle lead?
IEC C13 power cables are commonly referred to as kettle leads in the UK. Technically, however, IEC C13 is a specific connector type, so checking the equipment inlet is more reliable than relying on the informal name. What equipment does an IEC C13 lead fit?
It fits compatible electrical equipment equipped with an IEC C14 inlet. This connector format is widely used on electrical and electronic equipment. Can this be used as a replacement ballast power cable?
Yes, where the ballast uses a compatible IEC C14 power inlet and its electrical requirements are suitable for the lead. Will this fit every ballast?
No. Ballasts and other equipment can use different power connections, so check the connector and electrical requirements before ordering. Why choose a 5m power lead?
The additional cable length gives greater flexibility when equipment needs to be positioned further away from the available mains socket. Is IEC C13 the same as IEC C14?
No. They are the two mating sides of the connection. The C13 is the female connector on the power lead, while the C14 is the corresponding inlet normally fitted to the equipment. Is IEC C13 the same as IEC C15?
No. C13 and C15 are different IEC connector types. Always check the inlet fitted to your equipment before selecting a replacement power cable. Can I use the lead if the cable insulation is damaged?
No. A power lead with damaged insulation, exposed conductors, damaged pins or a damaged connector should not be used. Can the cable be used around water?
Electrical plugs and connections should be kept protected from water and excessive moisture. Installation should always follow the requirements of the equipment and the electrical environment. How many leads are in an outer case?
The outer case quantity for this product is 25 leads.
£2.95
Unit price per£2.95
Unit price perThis 2m black UK power lead provides a straightforward replacement mains connection for compatible electrical equipment fitted with an IEC C14 power inlet.
Commonly referred to as a kettle lead, IEC lead or computer power lead, the cable connects a standard UK 3-pin mains socket to compatible equipment using an IEC C13 female connector.
The practical 2 metre cable length provides useful reach without the excess cable associated with longer leads, making it well suited to lighting installations, controllers and other compatible electrical equipment.
It is particularly useful as a replacement for lost or damaged ballast power cables where the equipment uses a standard IEC C14 inlet.
Why choose the 2m UK IEC power lead?
UK plug to IEC C13 connection
The equipment end of the lead uses an IEC C13 female connector. This mates with the corresponding IEC C14 inlet commonly fitted to electrical equipment.
This connector format is widely used across computers, monitors, power supplies, controllers and compatible lighting equipment, including some ballasts.
Always check the inlet fitted to your equipment before ordering. IEC connectors are available in several different formats and a similar-looking connector does not necessarily mean the lead is suitable for the equipment.
Practical 2 metre cable length
At 2 metres long, this cable provides a useful balance between reach and cable management. It is long enough for many equipment installations without leaving large amounts of unnecessary cable to manage.
The additional reach can also help avoid placing unnecessary tension on either the mains plug or the equipment connector.
Route the cable carefully so that it is protected from sharp edges, crushing and excessive tension, and avoid positioning it where it could create a trip hazard.
Replacement power lead for compatible equipment
Equipment using a detachable IEC power connection can normally have the lead replaced independently if the original cable becomes lost or damaged.
This 2m cable provides a replacement UK mains connection for compatible equipment requiring an IEC C13 connector.
Always confirm both the connector type and the electrical requirements of the equipment before use. A connector physically fitting the appliance does not by itself confirm suitability for every electrical load or application.
Power lead installation & safety
2m UK Power Lead product details
| Product type | UK mains power lead |
|---|---|
| Cable length | 2m |
| Colour | Black |
| Mains connection | UK 3-pin plug |
| Equipment connection | IEC C13 female connector |
| Compatible equipment inlet | IEC C14 |
| Common description | Kettle lead / IEC power lead |
| Typical use | Replacement mains connection for compatible electrical equipment and lighting ballasts |
| Outer case quantity | 50 leads |
2m UK IEC Power Lead FAQs
How long is this power lead?
The cable is 2 metres long, providing practical reach for connecting compatible equipment to a nearby mains socket. What connector is on the equipment end?
The equipment end uses an IEC C13 female connector, designed to mate with a compatible IEC C14 inlet. Does it have a UK plug?
Yes. The mains end is fitted with a UK 3-pin plug. Is this commonly called a kettle lead?
Yes. IEC C13 power cables are commonly described as kettle leads in the UK, although IEC C13 is the more precise connector description. What equipment does an IEC C13 power lead fit?
It connects to compatible electrical equipment fitted with an IEC C14 inlet. Can I use it as a replacement ballast power cable?
Yes, where the ballast uses a compatible IEC C14 inlet and the power lead is suitable for the ballast's electrical requirements. Will it fit every lighting ballast?
No. Different ballasts can use different power connections, so check the equipment connector before ordering. What is the difference between IEC C13 and C14?
The C13 is the cable-mounted connector on this power lead. It connects to the corresponding C14 inlet fitted to compatible equipment. Why choose a 2m power lead?
A 2m cable provides useful reach while remaining relatively easy to route and manage around electrical equipment. Can this replace a lost IEC power cable?
Yes, provided the original equipment uses the same compatible IEC connection and the replacement lead meets its electrical requirements. Can I use a damaged power lead?
No. Do not use a lead if the cable insulation, mains plug or equipment connector shows signs of damage. Should the connections be kept dry?
Yes. Electrical plugs and connections should be protected from water and excessive moisture and installed appropriately for the operating environment. How many 2m power leads are in an outer case?
The outer case quantity for this product is 50 leads.
£2.50
Unit price per£2.50
Unit price perThe Loadstar 300W Dual Spectrum CFL is a high-output compact fluorescent plant lamp designed to provide a mixed light spectrum suitable for use across vegetative growth and flowering.
Rather than using a spectrum focused primarily on one stage of plant development, the dual spectrum output combines light suited to both vegetative and flowering growth. This makes the lamp a practical option where one CFL is required for use throughout the crop cycle.
The lamp uses a large E40 screw fitting and incorporates its operating electronics within the lamp assembly, so it does not require the separate HID ballast used with conventional HPS or metal halide lamps.
At 300W, this is one of the higher-powered CFL options in the Loadstar range and is suited to propagation, vegetative growth, supplementary lighting and smaller-scale full-cycle plant lighting where CFL technology is preferred.
Why choose the Loadstar 300W Dual Spectrum CFL?
Dual spectrum light for growth & flowering
Plant lighting requirements change as a crop develops. Blue-weighted light is commonly associated with compact vegetative development, while increased red light is particularly useful during flowering and fruiting.
A dual spectrum CFL combines these requirements into one lamp rather than concentrating almost entirely on either a blue growth spectrum or a red flowering spectrum.
This makes the Loadstar 300W Dual Spectrum CFL particularly convenient where the same lamp is intended to remain in use as plants move from propagation and vegetative development into flowering.
It can also be used as supplementary lighting alongside another suitable primary light source where additional mixed-spectrum light is required.
Self-ballasted CFL technology
The Loadstar 300W is a compact fluorescent lamp with integrated operating electronics. Unlike a conventional HPS or metal halide lamp, it does not require a separate external HID ballast to operate.
This simplifies the lighting arrangement considerably. When fitted to an electrically suitable E40 CFL lamp holder or compatible reflector, the lamp can operate from the appropriate mains-powered holder without a separate ballast positioned elsewhere in the installation.
This distinction is important when selecting equipment. An E40 fitting describes the physical lamp base, but does not mean that every E40 lamp and holder combination is automatically compatible. Always use a holder designed for the electrical requirements and weight of the lamp.
Where can a 300W CFL be used?
The 300W output gives this Loadstar lamp considerably more lighting capacity than smaller propagation CFLs, making it useful across several types of plant-lighting application.
Positioning a 300W CFL lamp
CFL lamps generally produce less intense radiant heat than traditional HID lamps, allowing them to be used effectively in applications where managing heat is important.
However, a 300W CFL still produces heat and requires suitable clearance and airflow. Lamp-to-canopy distance should therefore be determined by observing plant response, light coverage and temperature rather than assuming the lamp can be positioned extremely close to foliage.
When used with a reflector, position the lamp to achieve an even spread across the intended plant area. When used as supplementary lighting, the lamp can be positioned to increase illumination in areas that receive less light from the primary fixture.
Installation & lamp handling
Loadstar 300W Dual Spectrum CFL product details
| Brand | Loadstar |
|---|---|
| Product type | Compact fluorescent plant lamp |
| Power | 300W |
| Spectrum | Dual spectrum |
| Lamp fitting | E40 screw fitting |
| Ballast arrangement | Self-ballasted / integrated operating electronics |
| Suitable crop stages | Propagation, vegetative growth and flowering |
| Typical applications | Full-cycle and supplementary plant lighting |
| Outer case quantity | 10 lamps |
Loadstar 300W Dual Spectrum CFL FAQs
What does dual spectrum mean on a CFL lamp?
Dual spectrum means the lamp combines light suited to vegetative development with light suited to flowering, allowing one lamp to be used across different stages of plant growth. Does the Loadstar 300W CFL need a separate ballast?
No separate HID ballast is required. The CFL incorporates its operating electronics into the lamp assembly and should be fitted to a suitable E40 CFL lamp holder. What lamp fitting does the 300W Loadstar CFL use?
It uses an E40 large Edison screw fitting. Check that the lamp holder is designed for a high-output CFL of this type before installation. Can I use the same lamp for vegetative growth and flowering?
Yes. That is the main advantage of the dual spectrum version. Its mixed output allows the same lamp to remain in use as plants progress from vegetative development into flowering. How is this different from the Loadstar Blue Spectrum CFL?
A blue-spectrum CFL is primarily intended for propagation and vegetative development. The dual spectrum version provides a broader balance suited to both vegetative and flowering stages. Can this lamp be used for supplementary plant lighting?
Yes. A CFL can be positioned to supplement an existing lighting system, particularly where additional light is required around the edges or lower-intensity areas of the main lighting footprint. Can I use the 300W CFL with a reflector?
Yes, provided the reflector has a suitable E40 lamp holder and is designed to accommodate the physical size, weight and electrical requirements of the lamp. Can it be used with a hanging E40 CFL lamp holder?
Yes, where the holder is electrically suitable for the lamp and provides secure mechanical support. The lamp should never be suspended by the electrical cable itself. Does a 300W CFL still produce heat?
Yes. Although CFL technology generally produces less intense radiant heat than traditional HID lighting, a 300W lamp still generates significant heat and requires suitable clearance and airflow. How close should a 300W CFL be to plants?
There is no single correct distance for every installation. Positioning depends on the reflector or holder, plant stage, environmental temperature and plant response. Adjust the height to achieve useful light coverage without causing heat or light stress. How should a used CFL lamp be disposed of?
Fluorescent lamps require appropriate disposal because they contain materials that should not be placed in normal household or commercial general waste. Use an appropriate lamp recycling or WEEE disposal route. How many Loadstar 300W Dual Spectrum CFL lamps are in an outer case?
The outer case quantity is 10 lamps.
£43.75
Unit price per£43.75
Unit price perThe Philips MASTER GreenPower Xtra 1000W EL DE is a professional double-ended high-pressure sodium (HPS) lamp developed for high-output horticultural lighting, delivering an initial photon flux of approximately 2150µmol/s.
Designed for use with suitable high-frequency electronic control gear, the GreenPower Xtra combines very high plant-light output with strong output maintenance over its operating life. Philips developed the Xtra generation specifically to improve growth-light performance and maintenance in professional crop-production environments.
The lamp uses a K12x30s double-ended base and operates horizontally in compatible 1000W DE fixtures. Its clear tubular construction minimises obstruction between the arc tube and reflector, while the double-ended design allows accurate positioning within compatible optical systems.
With a 2000K colour temperature and the characteristic red-rich output of horticultural HPS technology, the lamp is particularly suited to high-intensity flowering and fruiting applications as well as commercial supplementary lighting.
Why choose the Philips MASTER GreenPower Xtra 1000W?
2150µmol/s high-output horticultural lighting
For plant lighting, photon output is a much more useful performance measure than simply comparing lamps by visible brightness. The Philips MASTER GreenPower Xtra produces an initial photon flux of approximately 2150µmol/s, placing it firmly within professional high-intensity horticultural lighting.
This high photon output allows suitable fixtures to deliver substantial photosynthetically active light over the crop area. Actual PPFD at canopy level will depend on the fixture, reflector, mounting height, spacing, room geometry and overall lighting layout.
For commercial installations, fixture spacing and mounting height should therefore be determined from an appropriate lighting plan rather than lamp wattage alone.
Designed for strong light-output maintenance
Initial output is only part of the performance of a professional horticultural lamp. As discharge lamps accumulate operating hours, their output gradually declines.
Philips designed the GreenPower Xtra range to provide strong growth-light maintenance over its service period. Published Philips horticultural data specifies an initial photon flux of approximately 2150µmol/s and a maintained value of approximately 2040µmol/s after 10,000 operating hours.
This high level of output retention is particularly valuable in professional crop production, where declining lamp performance can gradually reduce the amount of light reaching the crop even though the lamps continue to operate normally.
2000K HPS spectrum for flowering & fruiting crops
The MASTER GreenPower Xtra has a nominal colour temperature of 2000K, producing the warm, red-rich spectral profile characteristic of horticultural high-pressure sodium lighting.
HPS remains particularly effective for flowering and fruiting crops and is also widely used as high-intensity supplementary lighting in professional greenhouse production.
Where spectral balance is an important part of the crop strategy, the HPS output can also be considered alongside natural daylight or other artificial lighting technologies within the overall lighting design.
Double-ended K12x30s lamp design
Unlike a conventional single-ended HPS lamp, the GreenPower Xtra is supported and electrically connected at both ends using a K12x30s double-ended base.
This construction allows the lamp to sit horizontally within a compatible reflector and removes the need for the internal return-frame arrangement associated with many traditional single-ended HID lamps.
The lamp must only be used in a fixture specifically designed for the correct double-ended lamp format and electrical operating requirements. It is not interchangeable with a conventional E40 screw-fit HPS lamp.
Requires compatible electronic control gear
The MASTER GreenPower Xtra 1000W EL is designed for operation with compatible high-frequency electronic control gear. The lamp cannot be connected directly to the mains supply.
Correct matching between the lamp, electronic ballast and fixture is essential. The ballast must provide the electrical operating characteristics required by this specific lamp type.
Do not assume that any ballast labelled simply as 1000W is suitable. Compatibility should be confirmed against the ballast or fixture manufacturer's specifications before installation.
Operating position & heat management
Philips specifies this lamp for parallel or horizontal operation. It should therefore be installed in a compatible fixture that maintains the correct lamp orientation.
A 1000W HPS system produces substantial radiant and convective heat. Appropriate fixture clearance, air movement and environmental control are essential when designing the installation.
The lamp and fixture become extremely hot during operation. Allow adequate cooling time before handling, servicing or replacing the lamp.
Philips MASTER GreenPower Xtra 1000W EL DE product details
| Brand | Philips |
|---|---|
| Product range | MASTER GreenPower Xtra |
| Lamp technology | High-pressure sodium (HPS) |
| Nominal lamp class | 1000W |
| Published power consumption | 1020W |
| Initial photon flux | Approximately 2150µmol/s |
| Maintained photon flux | Approximately 2040µmol/s at 10,000 operating hours |
| Colour temperature | 2000K |
| Cap / base | K12x30s double-ended |
| Bulb shape | T40 clear tubular |
| Operating position | Parallel / horizontal |
| Dimmable | Yes, with compatible control gear and within manufacturer operating requirements |
| Control gear | Compatible high-frequency electronic ballast required |
| Rated operating life | 10,000 hours |
| Typical application | High-intensity professional horticultural and greenhouse crop lighting |
Philips MASTER GreenPower Xtra 1000W FAQs
What is the light output of the Philips GreenPower Xtra 1000W?
Philips specifies an initial horticultural photon flux of approximately 2150µmol/s, making it a very high-output HPS lamp for professional crop lighting. How well does the GreenPower Xtra maintain its output?
Published Philips horticultural data gives an initial output of approximately 2150µmol/s and around 2040µmol/s after 10,000 operating hours, demonstrating strong photon-output maintenance over its rated life. Is this a double-ended HPS lamp?
Yes. It uses a K12x30s double-ended base and must be installed in a compatible double-ended horticultural fixture. Will this lamp fit an E40 reflector?
No. An E40 reflector uses a large screw-type lamp holder. This Philips lamp uses a K12x30s double-ended fitting and requires the appropriate DE fixture. Does the lamp need a ballast?
Yes. The lamp requires compatible high-frequency electronic control gear and must not be connected directly to the mains supply. Can I use any 1000W electronic ballast?
Not automatically. Ballast compatibility depends on the electrical operating requirements of the lamp. Confirm that the specific ballast or fixture is approved for this type of Philips 1000W EL double-ended lamp. What does 2000K mean for plant lighting?
2000K describes the lamp's warm colour temperature. The resulting HPS spectrum is strongly weighted towards yellow, orange and red wavelengths and is widely used for flowering, fruiting and supplementary greenhouse lighting. Can the Philips GreenPower Xtra 1000W be dimmed?
Philips lists the lamp as dimmable. Dimming must be carried out using compatible electronic control gear and within the operating limits specified for the lamp and ballast combination. Why is photon flux measured in µmol/s rather than lumens?
Lumens describe light according to human visual sensitivity. Photon flux expressed in µmol/s is more relevant to horticultural lighting because it quantifies the photosynthetically active photons produced by the light source. Can the lamp be mounted vertically?
Philips specifies parallel or horizontal operation for this lamp. It should be installed in a compatible fixture that maintains the required operating position. When should a horticultural HPS lamp be replaced?
A discharge lamp can continue operating after its useful plant-light output has begun to decline. Professional installations commonly manage replacement according to operating hours and measured light performance rather than waiting for the lamp to fail completely. How should a used Philips HPS lamp be disposed of?
HID lamps contain materials including mercury and require appropriate lamp recycling rather than disposal with general waste. If a lamp breaks, follow Philips' handling guidance and use an appropriate recycling or hazardous-lamp waste route.
£6.85
Unit price per£6.85
Unit price perThe Loadstar Pro 600W Dual Spectrum HPS Lamp is a cost-effective high-intensity discharge lamp designed to provide useful light for both vegetative growth and flowering from a single 600W bulb.
Unlike a conventional flowering-focused HPS lamp, the Loadstar Pro uses a dual-spectrum output that supplements the characteristic red and orange HPS spectrum with additional blue light. This gives plants a broader spectrum and allows the same lamp to be used throughout the main growth and flowering stages.
The Loadstar Pro is designed for use with compatible 600W HID lighting equipment and is suitable as a replacement lamp for existing 600W HPS systems or as part of a new 600W lighting installation.
It provides a straightforward option for growers who want the proven intensity of 600W HID lighting without changing between separate vegetative and flowering lamps.
Why choose the Loadstar Pro 600W Dual Spectrum Lamp?
Dual spectrum for growth & flowering
Standard high-pressure sodium lamps are particularly strong in the warmer red and orange areas of the spectrum. This makes HPS technology particularly useful during flowering and fruiting, but a conventional HPS spectrum is less balanced towards blue wavelengths.
A dual-spectrum HPS lamp introduces additional blue light while retaining the strong warm-spectrum characteristics of HPS. The result is a more versatile lamp that can support vegetative development as well as flowering and fruiting.
For growers who prefer to run one type of HID lamp throughout the crop cycle, this avoids the need to swap between a separate metal halide growth lamp and HPS flowering lamp.
Suitable applications
Using the Loadstar Pro 600W lamp
The Loadstar Pro must be operated with a suitable 600W HID ballast and compatible reflector or lamp holder. The ballast regulates the electrical supply required to start and operate the HID lamp correctly.
Always switch off and isolate the lighting system before fitting, removing or inspecting the lamp. Allow the lamp and reflector to cool fully before handling, as HID lamps and surrounding lighting equipment can become extremely hot during operation.
Ensure the lamp is securely fitted and use only equipment rated for the lamp type and wattage. HID lamps should not be connected directly to the mains without the appropriate ballast.
Replacing older HPS lamps
HID lamps gradually lose useful light output as they age, even when the lamp continues to illuminate normally. This means an older lamp can appear to be working while providing less effective light than when it was new.
Replacing ageing lamps is therefore an important part of maintaining an established HID lighting installation. The Loadstar Pro provides a cost-effective replacement for compatible 600W systems while retaining dual-spectrum operation across both vegetative and flowering stages.
Loadstar Pro 600W product details
| Brand | Loadstar |
|---|---|
| Range | Loadstar Pro |
| Product type | Dual-spectrum HPS lamp |
| Lamp technology | High Pressure Sodium (HPS) |
| Power | 600W |
| Spectrum | Dual spectrum |
| Suitable crop stages | Vegetative growth, flowering & fruiting |
| Ballast required | Yes - compatible 600W HID ballast required |
| Typical use | Plant lighting, controlled-environment horticulture & replacement lamp for compatible 600W HPS systems |
| Outer case quantity | 25 lamps |
Loadstar Pro 600W Dual Spectrum Lamp FAQs
What type of lamp is the Loadstar Pro 600W?
It is a 600W dual-spectrum High Pressure Sodium (HPS) lamp designed for plant lighting applications. What does dual spectrum mean?
A dual-spectrum HPS lamp supplements the strong red and orange output associated with HPS technology with additional blue light, producing a more versatile spectrum for different stages of plant development. Can I use the Loadstar Pro 600W for vegetative growth?
Yes. The additional blue component of its dual-spectrum output makes the lamp suitable for vegetative growth as well as later crop stages. Can I use it for flowering and fruiting?
Yes. The Loadstar Pro retains the strong warm-spectrum output associated with HPS lighting and is suitable for flowering and fruiting crops. Can I use the same lamp throughout the crop cycle?
Yes. One of the main advantages of a dual-spectrum HPS lamp is its ability to provide useful light for both vegetative and flowering stages without changing between separate growth and bloom lamps. Does the Loadstar Pro 600W need a ballast?
Yes. This is an HID lamp and requires a compatible 600W ballast to start and regulate the lamp correctly. Can I connect this 600W HPS bulb directly to the mains?
No. A suitable HID ballast and compatible lighting equipment are required. Never connect an HID lamp directly to a mains electrical supply. Will it work with a 600W digital ballast?
It is designed for compatible 600W HPS lighting systems. Always confirm that the individual ballast is rated for the lamp type and 600W operating power before use. Can it replace an existing 600W HPS lamp?
Yes, provided the existing ballast, reflector and lamp holder are compatible with this type of 600W HPS lamp. Is this a metal halide lamp?
No. The Loadstar Pro is a dual-spectrum HPS lamp. Its spectrum contains an additional blue component for improved versatility, but it is not a metal halide lamp. Does an HPS lamp lose output as it gets older?
Yes. HID lamps gradually lose useful light output with operating time, so an older lamp can continue illuminating while producing less effective plant light than it did when new. Does a 600W HPS lamp produce heat?
Yes. HID lighting produces substantial heat during operation. Appropriate ventilation, clearance and temperature management should be considered when designing the lighting installation. Is the Loadstar Pro supplied as a complete lighting system?
No. This product is the 600W dual-spectrum lamp. A compatible ballast, reflector, lamp holder and associated electrical equipment are required to form a complete lighting system. How many Loadstar Pro 600W lamps are in an outer case?
The outer case quantity for this SKU is 25 lamps.
£5.00
Unit price per£5.00
Unit price perThe Loadstar Pro 1000W SE HPS Lamp is a high-output single-ended high-pressure sodium lamp designed primarily for the flowering and fruiting stages of plant development.
Producing the predominantly red and yellow light associated with traditional HPS technology, this 1000W lamp is designed for applications where powerful flowering illumination and a large usable lighting footprint are required.
The single-ended (SE) format is designed for compatible 1000W SE reflectors and lighting systems, distinguishing it from the Loadstar Pro 1000W DE lamp used in double-ended fixtures.
As a high-intensity discharge lamp, the Loadstar Pro requires a compatible 1000W ballast to operate and cannot be connected directly to the mains supply.
Why choose the Loadstar Pro 1000W SE HPS Lamp?
Red-rich HPS spectrum for flowering & fruiting
The Loadstar Pro 1000W SE produces the predominantly red and yellow spectral output characteristic of high-pressure sodium lighting.
This spectral balance makes the lamp particularly suited to flowering and fruiting applications, where high-intensity red-rich lighting can support strong reproductive growth.
The lamp can also form part of a broader crop-lighting strategy where HPS is combined with natural daylight or other artificial light sources.
High-output 1000W plant lighting
At 1000W, the Loadstar Pro is intended for significantly larger and higher-intensity applications than conventional 250W, 400W or 600W HPS systems.
The increased power allows a suitable reflector to distribute substantial light across a larger crop area, although actual canopy intensity depends on the reflector, mounting height, spacing and surrounding environment.
Higher wattage should not automatically be treated as better for every installation. A 1000W HPS lamp is most effective where the available area, mounting height, ventilation and environmental control are appropriate for its output.
What does SE mean?
SE stands for single-ended. The lamp's electrical and mechanical connection is located at one end, allowing it to fit a compatible single-ended reflector or lamp holder.
This is different from a DE or double-ended HPS lamp, which is supported and connected at both ends and requires a completely different type of fixture.
The Loadstar Pro 1000W SE should therefore only be used with equipment specifically suitable for a 1000W single-ended HPS lamp.
Requires a compatible 1000W ballast
High-pressure sodium lamps require dedicated control gear to start the lamp and regulate its operation. The Loadstar Pro 1000W SE therefore cannot be connected directly to the mains supply.
Use a compatible 1000W ballast designed to operate single-ended HPS lamps. Loadstar also produces a 1000W SE digital ballast specifically intended for single-ended 1000W lighting systems.
Where a ballast provides adjustable output settings, follow the ballast and lamp manufacturers' operating requirements. Do not assume that every ballast carrying a 1000W rating is automatically compatible with every 1000W lamp.
Heat management & positioning
A 1000W HPS lamp produces a substantial amount of heat as well as high-intensity light. Appropriate ventilation and environmental management are therefore essential.
Mounting height should be selected according to the reflector, crop, environmental temperature and measured or observed light intensity. Adequate clearance should always be maintained between the lamp, reflector, plants and surrounding materials.
The lamp and reflector become extremely hot during operation. Always switch the lighting system off and allow sufficient cooling time before handling, servicing or replacing the lamp.
Loadstar Pro 1000W SE HPS Lamp product details
| Brand | Loadstar |
|---|---|
| Range | Loadstar Pro |
| Product type | High-pressure sodium horticultural lamp |
| Lamp power | 1000W |
| Lamp format | Single-ended (SE) |
| Light spectrum | Predominantly red and yellow |
| Primary crop stage | Flowering and fruiting |
| Control gear | Compatible 1000W SE HPS ballast required |
| Direct mains operation | No |
| Fixture requirement | Compatible single-ended 1000W reflector / lamp holder |
| Typical application | High-intensity flowering, fruiting and supplementary crop lighting |
Loadstar Pro 1000W SE HPS Lamp FAQs
What is the Loadstar Pro 1000W SE HPS lamp primarily designed for?
Its predominantly red and yellow HPS spectrum makes it particularly suited to high-intensity flowering and fruiting applications. What does SE mean on the Loadstar 1000W lamp?
SE means single-ended. The lamp connects to the lighting fixture at one end, unlike a double-ended lamp that is supported and electrically connected at both ends. Is this the same as the Loadstar Pro 1000W DE lamp?
No. The SE and DE versions use different lamp and fixture formats. This product is the single-ended version and requires compatible SE equipment. Does the Loadstar 1000W SE lamp need a ballast?
Yes. HPS lamps require suitable control gear for starting and operation. This lamp requires a compatible 1000W ballast designed for single-ended HPS lighting. Can I plug the lamp directly into the mains?
No. The lamp must be operated through suitable HPS control gear and a compatible reflector or lamp holder. It must not be connected directly to the mains supply. Can I use it with the Loadstar 1000W SE digital ballast?
The Loadstar 1000W SE digital ballast is designed to operate single-ended 1000W lamps, making it the corresponding type of control gear for an SE lighting system. Always confirm the complete lamp, ballast and reflector configuration before installation. Is this a dual spectrum lamp?
This particular Loadstar Pro 1000W SE lamp is described as producing predominantly red and yellow light and is primarily positioned as a flowering HPS lamp, rather than the separate Loadstar dual spectrum lamp range. Can a 1000W HPS lamp cover more area than a 600W lamp?
A 1000W system provides substantially greater lamp power and can be used for larger high-intensity lighting footprints. Actual coverage depends on the reflector, mounting height, layout and required canopy light level rather than wattage alone. Does a 1000W HPS lamp produce a lot of heat?
Yes. A 1000W HPS lighting system produces substantial heat, so adequate ventilation, clearance and environmental control should form part of the installation design. Can I put this lamp into a double-ended reflector?
No. Single-ended and double-ended lamps use different mounting systems. This lamp requires a compatible single-ended reflector and lamp holder. How should the lamp be handled after use?
Switch off the lighting system and allow the lamp and reflector to cool fully before touching or servicing them. HID lamps operate at very high temperatures during use. How should an old HPS lamp be disposed of?
HID lamps should be handled through an appropriate lamp recycling or WEEE waste route rather than being placed in general waste.
£1.00
Unit price per£1.00
Unit price perThe Loadstar 250W Dual Spectrum Lamp is a high-pressure sodium plant lamp designed to provide a broader spectrum for both vegetative growth and flowering, making it a versatile choice for smaller HID lighting systems.
Unlike a conventional flowering-focused HPS lamp, a dual spectrum lamp supplements the strong red and orange output associated with sodium lighting with additional light in the blue region of the spectrum. This creates a more balanced output for use across multiple stages of plant development.
At 250W, the Loadstar offers a lower-power alternative to larger 400W and 600W HID systems. It is particularly useful where a compact lighting footprint is required or where the heat and power consumption of a larger HID lamp would be unnecessary.
The lamp requires a compatible 250W ballast and suitable HID reflector. It is not a self-ballasted lamp and must not be connected directly to the mains supply.
Why choose the Loadstar 250W Dual Spectrum Lamp?
Dual spectrum light for vegetative growth & flowering
Traditional high-pressure sodium lamps are particularly strong in the red, orange and yellow regions of the spectrum. This makes them highly effective during flowering and fruiting, but less balanced than some other light sources for vegetative development.
The Loadstar Dual Spectrum lamp broadens this output by providing additional blue light alongside the characteristic red-rich HPS spectrum.
The result is a more versatile lamp that can remain in use as plants move from vegetative development into flowering, rather than requiring a separate metal halide or blue-spectrum lamp for the earlier growth stage.
Where is a 250W dual spectrum lamp useful?
A 250W HID system occupies a useful position between lower-output propagation lighting and substantially more powerful 400W, 600W and 1000W systems.
Requires a compatible 250W ballast
The Loadstar 250W Dual Spectrum Lamp is an HID discharge lamp and therefore requires suitable control gear to start the lamp and regulate its electrical operation.
A compatible 250W ballast must be installed between the mains supply and lamp. The lamp must not be connected directly to the mains.
Loadstar produces a 250W magnetic ballast, while suitable multi-wattage digital ballasts may also support 250W sodium and dual spectrum lamps. Always confirm compatibility with the specific ballast before installation.
Pair with a suitable HID reflector
The reflector has a major influence on how effectively the lamp's output is distributed across the crop. A suitable reflector directs light that would otherwise travel upwards or sideways back towards the plant canopy.
Reflector shape, mounting height and positioning all affect the resulting lighting footprint. For the most uniform coverage, position the fixture centrally over the intended area and adjust its height according to crop response and environmental conditions.
Heat management & lamp positioning
Although a 250W HPS lamp produces less heat than higher-powered HID lamps, it still operates at a very high temperature and requires appropriate ventilation and clearance.
Lamp-to-canopy distance should be selected according to the reflector, environmental temperature, crop stage and plant response. Avoid positioning the lamp so close that foliage experiences excessive heat or light stress.
The lamp and reflector become extremely hot during operation. Always switch off the ballast and allow the system to cool fully before handling or carrying out maintenance.
Loadstar 250W Dual Spectrum Lamp product details
| Brand | Loadstar |
|---|---|
| Product type | Dual spectrum HID plant lamp |
| Lamp technology | High-pressure sodium (HPS) |
| Power | 250W |
| Spectrum | Dual spectrum |
| Primary spectral characteristics | Red-rich HPS output with additional blue-spectrum light |
| Suitable crop stages | Vegetative growth, flowering and fruiting |
| Ballast required | Yes - compatible 250W control gear required |
| Direct mains operation | No |
| Typical application | Full-cycle and supplementary plant lighting |
Loadstar 250W Dual Spectrum Lamp FAQs
What does dual spectrum mean?
A dual spectrum lamp combines the strong red-rich output associated with HPS lighting with additional blue light, creating a broader spectrum suitable for more than one stage of plant development. Can the Loadstar 250W Dual Spectrum Lamp be used for vegetative growth?
Yes. The additional blue component makes a dual spectrum lamp more suitable for vegetative development than a conventional flowering-focused HPS lamp. Is the lamp suitable for flowering?
Yes. The lamp retains the strong red, orange and yellow output characteristic of HPS technology, making flowering and fruiting key applications. Does this lamp need a separate ballast?
Yes. The Loadstar 250W Dual Spectrum Lamp requires compatible 250W control gear. It is not self-ballasted and must not be connected directly to the mains supply. Can it be used with a digital ballast?
Yes, provided the digital ballast is specifically compatible with 250W sodium or dual spectrum lamps. Some multi-wattage digital ballasts include a dedicated 250W setting. Can I use the same lamp from vegetative growth through flowering?
Yes. Full-cycle use is one of the main reasons for choosing a dual spectrum lamp, as it removes the need to change between separate vegetative and flowering lamps. Why choose 250W instead of a 600W HPS lamp?
A 250W system is better suited to smaller lighting areas or installations where the additional light output, electrical demand and heat generated by a 600W system are unnecessary. Can the lamp be used without a reflector?
A compatible reflector is normally recommended because it redirects otherwise wasted light towards the crop and helps create a more useful lighting footprint. Does a 250W HPS lamp produce much heat?
Yes. It produces less total heat than higher-powered HID lamps, but the lamp itself still operates at a very high temperature. Suitable ventilation, clearance and safe handling remain essential. How do I know when an HPS lamp needs replacing?
HID lamps gradually lose useful light output as they accumulate operating hours. Replacement is best based on operating time, visible lamp condition and measured lighting performance rather than waiting for complete lamp failure. Can a 250W lamp be run at a higher ballast setting?
Only operate the lamp at settings specifically approved for the lamp and ballast combination. Do not run a 250W lamp at a higher output simply because a multi-wattage ballast offers higher settings. How should a used HPS lamp be disposed of?
HID lamps should be sent through an appropriate lamp recycling or WEEE waste route rather than being disposed of with general waste.
£25.00
Unit price per£25.00
Unit price perThe Adjust-A-Wings Hellion 630W 4200K DE CMH Lamp is a professional double-ended ceramic metal halide lamp delivering approximately 1210µmol/s of broad-spectrum plant light with a high CRI of approximately 97.
Developed specifically for high-performance plant lighting, the 4200K version produces a broad, daylight-style spectrum with a substantial blue component alongside useful red and far-red wavelengths. This makes it particularly well suited to propagation, vegetative development, mother plants and mixed-spectrum lighting installations.
Unlike conventional HPS lighting, CMH technology produces a much broader spectral distribution. Adjust-A-Wings developed its DE-CMH lamps using Japanese ceramic arc-tube technology to provide high output, excellent colour quality and a spectrum designed specifically around plant development.
This is a 630W double-ended CMH lamp and requires a compatible 630W DE-CMH fixture and suitable low-frequency electronic control gear. It is not interchangeable with standard HPS, metal halide or E40 lamps simply because they share a similar wattage.
Why choose the Adjust-A-Wings 630W 4200K DE-CMH Lamp?
4200K broad-spectrum CMH lighting
The 4200K version of the Adjust-A-Wings 630W DE-CMH is designed around a cooler, daylight-style spectrum with considerably more blue light than a conventional HPS lamp.
This makes it particularly useful during propagation and vegetative development, where strong blue-spectrum availability can support compact, controlled plant structure and vigorous foliage development.
The output is not limited to blue wavelengths. CMH technology provides a broad spectral distribution extending across the visible spectrum and into useful UV and far-red regions, producing a much more balanced light profile than conventional sodium lighting.
Approximately 1210µmol/s photon output
The 4200K Adjust-A-Wings 630W DE-CMH produces approximately 1210µmol/s of photosynthetic photon flux, equivalent to an efficacy of approximately 1.92µmol/J.
PPF measures the total quantity of photosynthetically active photons produced by the lamp each second. For plant lighting, this provides a more meaningful indication of output than lumens, which are weighted according to human vision.
The amount of light ultimately reaching the crop as PPFD will depend on the reflector, fixture geometry, mounting height, spacing and overall lighting layout.
High CRI broad-spectrum output
With a colour rendering index of approximately CRI 97, the 4200K DE-CMH provides a much broader visible spectrum than traditional HPS lighting.
Plants under the lamp therefore appear considerably more natural in colour, making visual inspection easier while also reflecting the broader spectral distribution produced by the ceramic metal halide arc tube.
CRI itself is a human-vision measurement rather than a measure of plant-light efficiency, so it should be considered alongside PPF, spectrum and crop requirements rather than used as a standalone horticultural performance figure.
Ideal for mixed-spectrum lighting
Adjust-A-Wings specifically positions its 4200K DE-CMH technology as a strong partner for DE-HPS lighting in mixed-spectrum installations.
HPS provides powerful yellow, orange and red output, while the 4200K CMH contributes substantially more blue alongside its broader spectrum. Combining the technologies can therefore create a more balanced overall spectral profile than either source provides alone.
The lamp can also be used independently where its cooler broad-spectrum output is appropriate for the crop and lighting strategy.
Requires dedicated 630W DE-CMH control gear
The Adjust-A-Wings 630W DE-CMH is a specialist discharge lamp and must be operated with compatible 630W DE-CMH control gear.
Adjust-A-Wings developed dedicated low-frequency square-wave electronic control gear for its 630W CMH system. Correct ballast matching is important for lamp starting, stable operation, spectral performance and service life.
Do not connect the lamp directly to the mains and do not assume that a 600W, 630W or adjustable HPS ballast is suitable. Only use control gear specifically approved for the lamp type.
Lamp life & output maintenance
Adjust-A-Wings recommends replacing its 630W DE-CMH lamps according to accumulated operating time and lighting performance rather than waiting for complete lamp failure.
For installations operating around 18 hours per day, the manufacturer recommends replacement approximately every 12-18 months. Lamp output gradually declines with operating hours even though the lamp may continue to illuminate normally.
When commissioning a new lamp, Adjust-A-Wings recommends operating it at full rated power for its first 24 hours to season the lamp before using any compatible dimming function.
Installation & handling
Adjust-A-Wings 630W 4200K DE-CMH Lamp product details
| Brand | Adjust-A-Wings |
|---|---|
| Range | Hellion |
| Lamp technology | Ceramic metal halide (CMH / CDM) |
| Power | 630W |
| Lamp format | Double-ended (DE) |
| Colour temperature | 4200K |
| Photon flux | Approximately 1210µmol/s |
| Photon efficacy | Approximately 1.92µmol/J |
| Colour rendering | Approximately CRI 97 |
| Spectrum | Broad daylight spectrum with strong blue content and useful UV and far-red output |
| Arc tube | Japanese ceramic arc-tube technology |
| Control gear | Compatible 630W DE-CMH electronic ballast required |
| Direct mains operation | No |
| Typical applications | Propagation, vegetative development, mother plants, full-cycle and mixed-spectrum lighting |
Adjust-A-Wings 630W 4200K DE-CMH FAQs
What is the difference between CMH and HPS lighting?
CMH produces a much broader spectrum with substantially more blue light and excellent colour rendering. HPS is more heavily weighted towards yellow, orange and red wavelengths. Both technologies can be useful independently or together depending on the lighting strategy. What does 4200K mean?
4200K describes the lamp's colour temperature. It produces a cooler, daylight-style appearance with a strong blue component, making this version particularly useful for vegetative development and supplementary lighting. What is the PPF of the 630W 4200K lamp?
The 4200K version produces approximately 1210µmol/s of photosynthetic photon flux at its rated 630W output. Can the 4200K CMH lamp be used for flowering?
Yes. Its broad spectrum can support full-cycle plant development, although the 4200K version has a stronger blue component and is particularly well suited to vegetative or mixed-spectrum applications. Can it be combined with HPS lighting?
Yes. Adjust-A-Wings specifically promotes combining DE-CMH and DE-HPS systems where a broader mixed spectrum is required. The CMH contributes blue and broad-spectrum light while HPS provides strong yellow, orange and red output. Does this lamp use an E40 screw fitting?
No. This is the 630W double-ended version and requires a compatible DE-CMH fixture. It should not be confused with single-ended CMH lamps that use an E40-style base. Can I use a standard HPS ballast?
No. The lamp requires compatible control gear specifically designed for 630W DE-CMH operation. Correct ballast matching is essential for reliable lamp operation and lifespan. Why does the lamp have such a high CRI?
CMH technology produces a broad visible spectrum, giving the 4200K lamp a CRI of approximately 97. This produces a more natural-looking light than conventional HPS and makes visual crop inspection easier. How often should a 630W DE-CMH lamp be replaced?
Adjust-A-Wings recommends changing its CMH and DE-CMH lamps approximately every 12-18 months when operated for around 18 hours per day. Replacement timing should also take measured light output and operating hours into account. Should a new CMH lamp be run at full power first?
Yes. Adjust-A-Wings recommends running a new lamp at its full rated output for the first 24 hours to season it before using compatible dimming settings. Is this lamp suitable as a direct replacement for a 600W HPS lamp?
Not as a simple lamp swap. The 630W DE-CMH requires its own compatible fixture and CMH control gear, so ballast and lamp-holder compatibility must be checked before changing lighting technology. How should a used CMH lamp be disposed of?
Discharge lamps should be handled through an appropriate lamp recycling or WEEE waste route rather than being placed in general waste.
£25.00
Unit price per£25.00
Unit price perThe Adjust-A-Wings Hellion 630W 3100K DE CMH Lamp is a high-output double-ended ceramic metal halide lamp producing approximately 1200µmol/s PPF from a broad, warm full spectrum designed for complete plant development and particularly strong flowering performance.
The 3100K, or 3.1K, version combines the broad spectral characteristics of ceramic metal halide technology with a warmer output than the 4200K version. This gives the lamp a strong balance of wavelengths across the plant-active spectrum while increasing its suitability for flowering and fruiting crops.
Adjust-A-Wings developed the Hellion CMH range around purpose-designed Japanese ceramic arc tubes rather than adapting a general-purpose lamp. The result is a specialist plant-lighting lamp designed to work as part of the Hellion 630W DE-CMH system.
This is a double-ended 630W CMH lamp. It requires a compatible DE-CMH fixture and correctly matched low-frequency electronic ballast and must not be connected directly to the mains supply.
Why choose the Adjust-A-Wings 630W 3100K DE-CMH Lamp?
3100K spectrum for full-cycle plant development
The 3100K Hellion DE-CMH produces a warm broad-spectrum output rather than the heavily yellow and orange-biased spectrum associated with conventional HPS lighting.
It retains useful blue light for vegetative development while providing a stronger warm and red component than the 4200K Hellion CMH. This makes the 3100K version particularly versatile where one CMH spectrum is required throughout the complete crop cycle.
Adjust-A-Wings specifically describes its 3K lamps as strong standalone choices for all stages of growth, with particular suitability for flowering.
3100K or 4200K CMH?
Both versions use the same fundamental 630W double-ended CMH technology, but their spectral emphasis is different.
| 3100K / 3.1K | Warmer full spectrum. Excellent standalone option for full-cycle use and particularly well suited to flowering and fruiting. |
|---|---|
| 4200K / 4.2K | Cooler spectrum with additional blue. Particularly useful for vegetative development and supplementing warmer HPS lighting. |
For an installation using CMH as the principal light source throughout the crop cycle, the 3100K version is the more flowering-focused of the two spectrum options.
1200µmol/s photosynthetic photon flux
The Hellion 630W 3100K DE-CMH is rated at approximately 1200µmol/s PPF, with a photon efficacy of approximately 1.91µmol/J.
PPF measures the number of photons within the photosynthetically active range emitted by the lamp every second. It is therefore considerably more relevant to plant-lighting performance than a conventional lumen figure alone.
The actual photon density reaching the crop will depend on the reflector, mounting height, fixture spacing and overall lighting layout.
Why use ceramic metal halide?
CMH uses a ceramic arc tube to produce a broad and relatively continuous spectrum. This differs significantly from conventional HPS technology, which concentrates a much greater proportion of its output into yellow, orange and red wavelengths.
The broader output makes CMH particularly attractive where spectral quality is important as well as raw photon output. It also allows the 3100K Hellion lamp to support both vegetative and reproductive stages without changing lamp technology between crop stages.
CMH & HPS mixed-spectrum lighting
The 630W Hellion DE-CMH can also be incorporated alongside DE-HPS fixtures to create a mixed-spectrum installation.
CMH contributes a much broader range of wavelengths, including substantially more blue, while HPS contributes intense yellow, orange and red output. Combining the technologies allows professional lighting layouts to exploit the different spectral characteristics of both lamp types.
The comparable output of the Hellion 630W DE-CMH and higher-output DE-HPS systems makes the combination particularly useful where alternating lighting layouts are being designed.
Dedicated 630W DE-CMH lamp format
This lamp uses a K12x30s double-ended base and is designed for an appropriately rated double-ended lamp holder. Its specified operating position is horizontal within approximately ±15°.
The lamp must be installed in a compatible fixture and operated using correctly matched 630W DE-CMH control gear.
Do not attempt to fit the lamp into conventional single-ended E40 equipment. The double-ended 630W lamp and the smaller Adjust-A-Wings 315W single-ended CMH lamps use different connection systems.
Requires compatible low-frequency CMH control gear
The Hellion 630W DE-CMH was designed to operate with specialist low-frequency square-wave electronic control gear.
Correct ballast matching is important for reliable ignition, stable lamp operation, spectral performance and lamp life. A ballast should therefore be specifically approved for 630W DE-CMH operation.
Do not assume that a conventional 600W HPS ballast, 630W-rated ballast or adjustable HID ballast is compatible simply because its wattage is similar.
12,000-hour rated lamp life
The 630W 3100K DE-CMH has a rated average life of approximately 12,000 hours.
Adjust-A-Wings recommends changing its CMH and DE-CMH lamps approximately every 12-18 months when operated for 18 hours per day, helping maintain lighting performance rather than waiting until complete lamp failure.
A new lamp should initially be operated at its full rated output for the first 24 hours to season the lamp before any compatible dimming function is used.
Adjust-A-Wings Hellion 630W 3100K DE-CMH Lamp product details
| Brand | Adjust-A-Wings |
|---|---|
| Range | Hellion |
| Lamp technology | Ceramic metal halide (CMH / CDM) |
| Power | 630W |
| Lamp format | Double-ended (DE) |
| Colour temperature | 3100K / 3.1K |
| Photon flux | Approximately 1200µmol/s |
| Photon efficacy | Approximately 1.91µmol/J |
| Colour rendering index | Approximately CRI 88 |
| Luminous flux | Approximately 64,100 lumens |
| Rated average life | Approximately 12,000 hours |
| Base | K12x30s double-ended |
| Bulb designation | T40 |
| Operating position | Horizontal ±15° |
| Overall length | Approximately 390mm |
| Lamp weight | Approximately 283g |
| Control gear | Compatible 630W DE-CMH electronic ballast required |
| Typical applications | Full-cycle plant lighting, flowering, fruiting and mixed-spectrum installations |
Adjust-A-Wings 630W 3100K DE-CMH FAQs
Is 3100K CMH suitable for flowering?
Yes. Adjust-A-Wings positions its warmer 3K spectrum as an excellent standalone full-cycle lamp and particularly suitable for flowering. Can I use the 3100K lamp for vegetative growth?
Yes. Unlike a heavily red-biased flowering lamp, the broad CMH spectrum retains substantial light across the visible range, allowing the 3100K version to be used during vegetative development as well as flowering. What is the difference between the 3100K and 4200K Hellion lamps?
The 3100K version has a warmer spectrum and is particularly strong as a standalone full-cycle and flowering lamp. The 4200K version contains additional blue and is especially useful for vegetative development and supplementing HPS. What is the PPF of the 630W 3100K DE-CMH?
The lamp is rated at approximately 1200µmol/s PPF, with an efficacy of approximately 1.91µmol/J. Does this lamp fit an E40 lamp holder?
No. This is a double-ended lamp using a K12x30s base. The 315W single-ended CMH lamps in the Adjust-A-Wings range use a different lamp format. Can I run it from a normal 600W HPS ballast?
No. The lamp requires control gear specifically compatible with 630W DE-CMH technology. Similar wattage does not make an HPS ballast electrically compatible with a CMH lamp. Can the 630W CMH be used alongside DE-HPS lighting?
Yes. The Hellion DE-CMH system was designed with mixed-spectrum installations in mind, allowing the broader CMH spectrum to complement the strong yellow, orange and red output of DE-HPS lighting. How long is the lamp rated to last?
The 630W 3100K DE-CMH has a rated average life of approximately 12,000 operating hours. Useful plant-light output will gradually decline during that period. When does Adjust-A-Wings recommend replacing its CMH lamps?
For lamps operated around 18 hours per day, Adjust-A-Wings recommends replacement approximately every 12-18 months to maintain lighting performance. Can a new Hellion CMH lamp be dimmed immediately?
Adjust-A-Wings recommends operating a new lamp at full rated power for its first 24 hours to season it before using a compatible dimming function. What position should the 630W DE-CMH lamp operate in?
The lamp is specified for horizontal operation within approximately ±15°. It should always be installed correctly in a compatible double-ended fixture. How should a used DE-CMH lamp be disposed of?
Used discharge lamps should be handled through an appropriate lamp recycling or WEEE waste route rather than being placed in general waste.
£12.50
Unit price per£12.50
Unit price perThe Adjust-A-Wings Hellion 315W 4200K SE-CMH Lamp is a high-performance single-ended ceramic metal halide lamp delivering 578µmol/s PPF from a broad daylight spectrum, with an industry-standard E40 mogul base for use in compatible 315W CMH lighting systems.
Designed specifically for plant lighting, the 4200K lamp combines strong blue-spectrum output with a broad distribution of wavelengths across the photosynthetically active range. It is particularly well suited to propagation, vegetative development and mother plants, while its broad spectrum also allows it to be used throughout the complete crop cycle.
Adjust-A-Wings developed the Hellion 315W CMH lamps around bespoke Japanese ceramic arc tubes, rather than simply adapting a general-purpose discharge lamp. An XOS borosilicate outer jacket complements the specialist arc-tube design.
The lamp produces 578µmol/s PPF at 315W with a high CRI of approximately 95, giving it a broad, natural-looking output that differs substantially from the narrower spectral profile of conventional HPS lighting.
Why choose the Adjust-A-Wings 315W 4200K CMH Lamp?
4200K daylight spectrum
The 4200K Hellion lamp has a cooler spectral balance than the 3100K version, with additional blue light that makes it particularly useful during active vegetative development.
Its spectrum is considerably broader than conventional HPS lighting, extending across blue, green and red wavelengths rather than concentrating the majority of visible output into yellow, orange and red.
Adjust-A-Wings also designed its 4K CMH spectrum with useful deep-red output, allowing the lamp to remain effective beyond vegetative growth and making it suitable for complete crop-cycle lighting.
578µmol/s PPF from 315W
The Hellion 315W 4200K lamp produces a specified 578µmol/s photosynthetic photon flux, equivalent to approximately 1.85µmol/J.
PPF measures the quantity of photosynthetically active photons produced by the lamp every second and provides a more useful measure of plant-light output than lumens alone.
Actual PPFD at crop level will depend on the reflector, mounting height, fixture spacing and lighting layout. Adjust-A-Wings designed the lamp to work particularly effectively with its Hellion ballast and Defender reflector system.
High CRI broad-spectrum light
With a specified CRI of 95, the 4200K Hellion CMH produces a much more natural-looking visible spectrum than conventional high-pressure sodium lighting.
This makes visual inspection of foliage, colour and general crop condition easier under the operating light. CRI is primarily a human colour-rendering measurement, however, so plant-light performance should be judged using spectrum, PPF and PPFD alongside CRI.
Vegetative, mother plant & full-cycle lighting
Adjust-A-Wings positions its 4K CMH lamps as particularly effective for vegetative development, while retaining sufficient spectral breadth for use throughout the plant lifecycle.
4200K or 3100K CMH?
| 4200K / 4.2K | Cooler daylight spectrum with additional blue. Particularly suited to propagation, vegetative development, mother plants and supplementing warmer HPS lighting. |
|---|---|
| 3100K / 3.1K | Warmer broad spectrum. Particularly suited to standalone full-cycle applications and flowering. |
Both versions are broad-spectrum CMH lamps and can support multiple stages of crop development. The choice is primarily about the spectral emphasis required from the lighting system.
Single-ended E40 lamp format
Unlike the larger 630W Hellion DE-CMH lamps, this 315W version uses a conventional E40 mogul screw base.
This makes the physical lamp format compatible with appropriate E40 lamp holders and reflector assemblies. However, the presence of an E40 fitting does not mean the lamp can be operated by any E40 lighting system.
The electrical control gear must be specifically compatible with 315W CMH lamp technology.
Use with compatible 315W CMH control gear
The Hellion 315W lamp is designed to work with suitable 315W CMH electronic control gear. Adjust-A-Wings developed its own Hellion ultra-high-frequency electronic ballast alongside the lamp so the two components could operate as a matched lighting system.
Do not connect the lamp directly to the mains and do not operate it from a conventional HPS or metal halide ballast unless that control gear is specifically approved for the 315W CMH lamp.
Correct ballast matching is important for reliable ignition, stable output, spectral performance and lamp life.
Lamp life & replacement
The 315W 4200K Hellion CMH has a specified rated average life of approximately 12,000 hours.
Adjust-A-Wings recommends changing its 315W and 630W CMH lamps approximately every 12-18 months when operated for 18 hours per day to maintain lighting performance.
A new CMH lamp should initially be operated at its full rated output for the first 24 hours to season the lamp before using a compatible dimming function.
Adjust-A-Wings Hellion 315W 4200K SE-CMH Lamp product details
| Brand | Adjust-A-Wings |
|---|---|
| Range | Hellion |
| Lamp technology | Ceramic metal halide (CMH) |
| Power | 315W |
| Lamp format | Single-ended (SE) |
| Base | E40 mogul screw base |
| Colour temperature | 4200K / 4.2K |
| Photon flux | 578µmol/s |
| Photon efficacy | Approximately 1.85µmol/J |
| Colour rendering index | CRI 95 |
| Luminous flux | Approximately 32,700 lumens |
| Luminous efficacy | Approximately 104lm/W |
| Bulb type | T46 |
| Overall length | Approximately 198mm |
| Glass diameter | Approximately 46mm |
| Lamp weight | Approximately 125g |
| Operating position | Horizontal or vertical |
| Rated average life | Approximately 12,000 hours |
| Control gear | Compatible 315W CMH electronic ballast required |
| Typical applications | Propagation, vegetative development, mother plants, full-cycle and mixed-spectrum lighting |
Adjust-A-Wings 315W 4200K CMH Lamp FAQs
What is the PPF of the 315W 4200K Hellion lamp?
The lamp produces 578µmol/s of photosynthetic photon flux at its rated 315W output. What is the 4200K spectrum best suited to?
Its cooler broad spectrum and strong blue component make it particularly useful for propagation, vegetative development and mother plants. It can also be used throughout the complete crop cycle. Does the lamp have an E40 fitting?
Yes. The 315W single-ended Hellion CMH uses an industry-standard E40 mogul screw base. Can I put it into any E40 reflector?
The E40 base provides broad physical compatibility with suitable lamp holders, but the complete fixture must be appropriate for the lamp and the electrical control gear must be compatible with 315W CMH technology. Can I run it from a normal HPS ballast?
No. Use a ballast specifically designed or approved for 315W CMH operation. The fact that the lamp uses an E40 fitting does not make conventional HPS control gear compatible. What is the difference between this and the 630W DE-CMH lamp?
This model is a 315W single-ended lamp with an E40 base. The 630W version uses a double-ended format and requires a different fixture and compatible 630W DE-CMH control gear. Can the 4200K lamp be used alongside HPS?
Yes. Its broad spectrum and additional blue output make it particularly useful for increasing spectral diversity in an installation that also uses warmer HPS or DE-HPS lighting. How long is the lamp rated to last?
The manufacturer's technical specification gives the 315W 4200K lamp a rated average life of approximately 12,000 hours. When should the lamp be replaced?
Adjust-A-Wings recommends replacing its CMH lamps approximately every 12-18 months when operated for around 18 hours per day to maintain lighting performance. Can a new 315W CMH lamp be dimmed immediately?
Adjust-A-Wings recommends operating a new lamp at its full rated output for the first 24 hours before using a compatible dimming function. Can the lamp operate horizontally or vertically?
Yes. The manufacturer's technical specification permits both horizontal and vertical operating positions when the lamp is installed in a suitable fixture. How should a used CMH lamp be disposed of?
Used discharge lamps should be handled through an appropriate lamp recycling or WEEE waste route rather than being placed in general waste.
£25.00
Unit price per£25.00
Unit price perThe Adjust-A-Wings Hellion 1000W DE-CMH 4K is a high-output double-ended ceramic metal halide lamp developed to deliver an exceptionally broad, blue-rich spectrum from a powerful 1000W discharge platform.
Part of the specialist Hellion lighting range, this 4K lamp combines the high intensity associated with professional double-ended lighting with the broad spectral distribution for which ceramic metal halide technology is valued.
Its approximately 4000K colour spectrum provides a strong blue component alongside a broad distribution of visible wavelengths, making it particularly useful for vigorous vegetative development, maintaining compact plant structure and mixed-spectrum lighting strategies.
A major advantage of this specialist 1000W DE-CMH lamp is its ability to operate with the compatible 1000W Hellion electronic lighting system, allowing suitable Hellion installations to move between compatible DE-HPS and DE-CMH lamps without requiring completely separate lighting systems.
Why choose the Adjust-A-Wings 1000W DE-CMH 4K Lamp?
High-intensity 4K ceramic metal halide spectrum
Ceramic metal halide differs from conventional HPS by producing a much broader spectral distribution. Rather than concentrating most of its output into the yellow, orange and red regions, CMH provides substantially more blue light alongside a wider range of wavelengths.
The 4K spectrum is particularly useful where strong vegetative development is the priority. Increased blue content can help support compact morphology, controlled internodal development and dense vegetative growth when overall environmental conditions are correctly managed.
The broad spectrum also makes DE-CMH useful where growers want to introduce greater spectral diversity into a high-intensity lighting installation.
Ideal for mixed-spectrum lighting
Adjust-A-Wings has developed its Hellion lighting platform around the ability to use different discharge technologies strategically rather than treating every lamp as interchangeable in terms of spectrum.
DE-HPS provides particularly strong yellow, orange and red output, while DE-CMH introduces considerably more blue and a broader overall spectrum. Combining the two technologies within a larger installation can therefore provide a wider spectral profile than either lamp type alone.
This makes the 1000W 4K DE-CMH especially interesting for commercial growers operating larger multi-light installations where CMH and HPS fixtures can be arranged to provide complementary spectra across the crop.
Designed for the Hellion 1000W lighting platform
The 1000W DE-CMH lamp was developed as part of Adjust-A-Wings' Hellion professional lighting range.
One of the key benefits of this specialist lamp is the ability to use DE-CMH within a compatible 1000W Hellion installation. This gives growers greater flexibility when changing the spectral strategy of an existing lighting system.
This is a specialist HID lamp and must not be connected directly to the mains. It requires compatible control gear and a suitable double-ended lamp holder and reflector arrangement. Always confirm ballast and fixture compatibility before installation.
Where does a 4K DE-CMH lamp fit into a lighting programme?
Managing a 1000W high-intensity lamp
A 1000W discharge lamp produces substantial light and radiant heat. Correct reflector selection, lamp height, air movement and environmental control are therefore essential parts of the lighting installation.
Lamp-to-canopy distance should be determined according to reflector configuration, crop sensitivity, environmental conditions and measured light intensity rather than relying on wattage alone.
Adjust-A-Wings reflectors are specifically designed to spread light and dissipate heat efficiently, but the environmental load produced by a 1000W lamp must still be accounted for when designing the growing area.
Installation & lamp care
Double-ended HID lamps operate at high temperatures and should always be installed with the lighting system switched off and allowed to cool fully before handling.
Handle the lamp carefully and avoid unnecessary contact with the outer glass. Ensure both ends are correctly seated in the compatible DE lamp holders before operating the system.
Adjust-A-Wings recommends running a new compatible discharge lamp at its full rated power for the first 24 hours to season the lamp before using any supported dimming function.
If dimming adjustments are subsequently made through compatible Hellion control gear, allow sufficient time between adjustments in accordance with the manufacturer's instructions.
Maintaining lighting performance
HID lamps gradually lose output during use even though they may continue to illuminate normally. Professional growers should therefore consider lamp age and operating hours when assessing lighting performance rather than waiting for complete lamp failure.
Keep records of installation dates in multi-lamp facilities so lamps can be inspected and replaced systematically. Maintaining lamps as a matched group can also help keep output more consistent across larger production areas.
Adjust-A-Wings Hellion 1000W DE-CMH 4K Lamp product details
| Brand | Adjust-A-Wings |
|---|---|
| Range | Hellion |
| Lamp technology | DE-CMH / double-ended ceramic metal halide |
| Rated power | 1000W |
| Spectrum | 4K / approximately 4000K |
| Lamp format | Double-ended |
| Spectral characteristic | Broad-spectrum, blue-rich CMH output |
| Primary applications | Vegetative production, stock plants and mixed-spectrum professional lighting |
| System compatibility | Compatible Adjust-A-Wings Hellion 1000W lighting equipment |
| Control gear required | Yes - compatible electronic ballast required |
| Direct mains operation | No |
| Initial seasoning | Run at full rated power for the first 24 hours before supported dimming |
Adjust-A-Wings 1000W DE-CMH 4K Lamp FAQs
What does 4K mean on this Adjust-A-Wings lamp?
4K refers to an approximately 4000K colour spectrum. It produces a comparatively blue-rich light and is particularly useful during vegetative plant development. What is DE-CMH?
DE-CMH means double-ended ceramic metal halide. It combines ceramic metal halide lamp technology with a double-ended lamp format designed for compatible high-intensity lighting equipment. Is this the same as a 1000W HPS lamp?
No. Although both are high-intensity discharge technologies, CMH and HPS have distinctly different spectral characteristics. The 4K CMH lamp provides substantially more blue light and a broader overall spectrum. Can the 4K lamp be used for vegetative growth?
Yes. Vegetative production is one of the main applications for the blue-rich 4K spectrum, particularly where compact and vigorous plant development is required. Can I combine this lamp with DE-HPS lighting?
Yes. Mixed-spectrum installations are one of the useful applications of DE-CMH. The broader, blue-rich CMH spectrum can complement the warmer yellow, orange and red-rich output associated with DE-HPS. Can this lamp be plugged directly into the mains?
No. This is a specialist HID lamp and requires compatible electronic control gear, DE lamp holders and a suitable reflector or lighting fixture. Will it work with any 1000W ballast?
Do not assume that wattage alone determines compatibility. The ballast must be suitable for the specific lamp technology and operating requirements. Confirm compatibility before installing the lamp. Do I need to season a new lamp?
Adjust-A-Wings recommends operating a new compatible discharge lamp at its full rated power for the first 24 hours before using supported dimming functions. Why would I choose CMH instead of HPS?
The main difference is spectrum. CMH provides a broader spectral distribution with considerably more blue, while HPS concentrates more of its output in the yellow, orange and red regions. The appropriate technology depends on the crop stage and lighting strategy. Does a 1000W CMH lamp produce much heat?
Yes. A 1000W HID lamp is a powerful light source and produces significant heat. Reflector design, hanging position, ventilation and environmental management should all be considered when installing it. How should the lamp be handled?
Allow the lamp to cool fully before handling, avoid unnecessary contact with the glass and ensure both ends are correctly seated in compatible DE lamp holders before operation. When should a DE-CMH lamp be replaced?
Light output gradually declines with operating hours, so professional users should monitor lamp age and crop-lighting performance rather than waiting for complete failure. Maintaining an installation-date record is particularly useful in multi-lamp facilities.
£5.00
Unit price per£5.00
Unit price perThe Lumatek Daisy Chain 5m Control Cable is the genuine control link cable for connecting compatible Lumatek controllable LED fixtures together in series, allowing multiple lights to receive a stable and precise control signal.
Designed specifically for Lumatek's controllable LED lighting platform, the cable connects the Signal Out port of one compatible fixture to the Signal In port of the next. This allows a row or group of fixtures to be daisy-chained rather than requiring a separate controller connection to every light.
The cable uses M12 self-locking male and female connectors to provide a secure connection between fixtures and has a generous 5 metre length, providing flexibility when positioning lights across larger propagation, nursery and controlled-environment installations.
This is Lumatek product code LUMM0015 and is IP65 rated for additional protection in demanding growing environments.
Why choose the Lumatek 5m Daisy Chain Control Cable?
Connect Lumatek LED fixtures in series
The Daisy Chain Control Cable is used between compatible Lumatek LED fixtures once the first fixture has been connected to the appropriate lighting controller.
Simply connect the M12 self-locking male plug to the Signal Out connection on the first LED fixture, then connect the M12 self-locking female plug to the Signal In connection on the next fixture.
Additional compatible fixtures can then be linked in sequence using additional LUMM0015 cables, creating an organised control network across a multi-light installation.
Centralised Lumatek lighting control
Daisy-chaining is particularly useful in larger lighting installations because it allows multiple compatible fixtures to receive their control signal through a single linked network.
When used with the appropriate Lumatek controller and compatible LED fixtures, this arrangement allows supported lighting-control functions to be applied across groups of connected lights without individually wiring every fixture directly back to the controller.
Lumatek's Control Panel Plus 2.0 system can control up to 100 compatible fixtures across two zones, with up to 50 fixtures per zone. The exact controller cable and configuration required depends on the version of the Lumatek fixtures and controller being used.
How to install the Lumatek Daisy Chain Cable
Control cable, not a driver extension cable
The LUMM0015 should not be confused with Lumatek's LED driver extension cables. This product is specifically designed to link the control signal between compatible LED fixtures.
If the objective is to position a Lumatek LED driver remotely from its fixture, a different Lumatek extension cable is required. Likewise, the cable used between the lighting controller and the first fixture can differ according to the controller and fixture generation.
Check the model and connection ports on existing Lumatek equipment before ordering accessories for older installations.
Built for professional lighting installations
Lumatek specifies the LUMM0015 using UL 2464 3 x 22AWG cable with an IP65 rating. The cable has been designed to maintain a reliable control connection in environments where lighting equipment may operate for long periods under demanding conditions.
The self-locking M12 connectors also provide a more secure connection than a loose push-fit control plug, particularly where multiple fixtures and cables are installed overhead.
Lumatek Daisy Chain 5m Control Cable product details
| Brand | Lumatek |
|---|---|
| Product | Daisy Chain Control Cable |
| Product code | LUMM0015 |
| Application | Linking compatible Lumatek controllable LED fixtures in series |
| Cable length | 5m |
| Connection | M12 self-locking male to M12 self-locking female |
| Fixture connection | Signal Out to Signal In |
| Cable specification | UL 2464 3 x 22AWG |
| Temperature resistance | 80°C |
| Specified working temperature | -20°C to 105°C |
| Specified storage temperature | -25°C to 105°C |
| Ingress protection | IP65 |
| Compliance | RoHS compliant |
| Contents | 1 x Lumatek 5m Daisy Chain Control Cable |
Lumatek Daisy Chain 5m Control Cable FAQs
What is the Lumatek 5m Daisy Chain Cable used for?
It links compatible Lumatek controllable LED fixtures together so the control signal can pass from one fixture to the next within a multi-light installation. What is the Lumatek product code?
The official Lumatek product code for the 5m Daisy Chain Control Cable is LUMM0015. How long is the cable?
The cable is 5 metres long, allowing useful spacing between compatible fixtures in professional lighting installations. What connectors does the cable use?
The LUMM0015 uses M12 self-locking male and female connectors. The cable connects the Signal Out port of one compatible fixture to the Signal In port of the next. Is this a power cable?
No. This is a control link cable used for communication between compatible Lumatek LED fixtures. It does not replace the fixture's mains power connection. Is this the cable for connecting the driver remotely?
No. Lumatek uses a different extension-cable accessory when the LED driver needs to be positioned remotely from the fixture. LUMM0015 is specifically the daisy-chain control cable between compatible fixtures. How many cables do I need?
For a conventional daisy-chain arrangement, one LUMM0015 cable is required between each additional compatible fixture after the first. For example, linking two fixtures together requires one daisy-chain cable between them. Is the cable IP rated?
Yes. Lumatek specifies the LUMM0015 Daisy Chain Control Cable as IP65 rated. Can it be used with the Lumatek Control Panel Plus 2.0?
Yes, as part of a compatible Lumatek LED control installation. The cable between the controller and the first fixture is a separate controller cable, while LUMM0015 links subsequent compatible fixtures together. How many fixtures can a Lumatek Control Panel Plus 2.0 manage?
Lumatek specifies control of up to 100 compatible fixtures across two independent zones, with up to 50 fixtures in each zone. The correct cables and compatible fixture versions must be used. How do I know whether my Lumatek LED is compatible?
Check the fixture for compatible Signal In and Signal Out connections and confirm its model and generation against Lumatek's current accessory guidance. This is particularly important with older versions of Lumatek LED equipment. Can several 5m cables be used in the same installation?
Yes. Additional LUMM0015 cables are used to continue the daisy chain from one compatible fixture to the next.
£50.00
Unit price per£50.00
Unit price per
£1.00
Unit price per£1.00
Unit price perKrystal Rope Ratchet Hangers provide a simple, secure and fully adjustable way to suspend lighting, carbon filters, extraction fans and other equipment, with a combined load capacity of up to 68kg per pair.
Supplied as a twin pack, the two ratchet hangers allow equipment to be raised, lowered and levelled without repeatedly unhooking it or adjusting chains and fixed-length supports.
Each hanger combines strong rope with an automatic locking ratchet mechanism and metal carabiner-style clips. Pulling the free end of the rope raises the suspended equipment, while the ratchet holds the selected position securely. The release mechanism allows the equipment to be lowered again when required.
This makes Krystal Rope Ratchets particularly useful for lighting installations where hanging height needs regular adjustment, as well as filters, fans and other equipment that may need repositioning during installation or maintenance.
Why choose Krystal Rope Ratchet Hangers?
Ideal for lighting, filters & ventilation equipment
Rope ratchets are one of the most versatile suspension accessories in an indoor horticultural installation because the same simple system can support a wide range of equipment.
Fast, precise lighting height adjustment
Lighting height often needs to change as plants develop or when a different fixture is installed. Fixed chains and basic hanging cords can make these adjustments unnecessarily awkward.
With Krystal Rope Ratchets, the fixture remains suspended while its position is adjusted. Pull the free rope through the ratchet to raise the light, then allow the locking mechanism to hold it at the required height.
Using one ratchet at each suspension point also allows the two sides of a fixture to be adjusted independently, helping keep lighting level over the crop.
Hang carbon filters & extraction equipment
Rope ratchets are equally useful when installing carbon filters and suitable extraction equipment overhead. The adjustable design can make positioning considerably easier than fixed straps or chains, particularly when aligning a filter with a fan or ducting run.
Always check the complete suspended weight before installation. The stated 68kg rating applies to the pair, so the load should be distributed correctly between both ratchets rather than concentrated onto a single hanger.
How to use Krystal Rope Ratchets
Never release a heavily loaded ratchet without supporting the equipment. Make small adjustments to each side to keep the load balanced.
Safe suspension starts with a secure fixing point
A rope ratchet can only support equipment safely when the structure above it is also capable of carrying the load. Always attach the hangers to a strong structural support or properly installed fixing suitable for the combined equipment weight.
Inspect the rope, ratchet mechanism, clips and attachment points periodically, particularly when supporting equipment continuously. Replace the hanger if the rope becomes damaged or frayed, a clip is distorted or the ratchet no longer locks positively.
The 68kg rating is the combined capacity of the pair. Do not treat this figure as the load rating of each individual ratchet.
Krystal Rope Ratchet Hangers product details
| Brand | Krystal |
|---|---|
| Product type | Adjustable rope ratchet equipment hangers |
| Pack quantity | 2 rope ratchet hangers |
| Maximum load | 68kg per pair |
| Adjustment | Fully adjustable ratchet mechanism |
| Attachment | Metal carabiner-style clips |
| Primary applications | Lighting, carbon filters, extraction fans and other suitable suspended equipment |
| Outer case quantity | 100 packs |
Krystal Rope Ratchet Hangers FAQs
How many rope ratchets are supplied?
Each pack contains two Krystal Rope Ratchet Hangers, allowing equipment to be supported and adjusted from two mounting points. How much weight can the Krystal Rope Ratchets hold?
The pair is rated to support a combined load of up to 68kg when correctly installed and the weight is properly distributed across both hangers. Is the 68kg rating for each ratchet?
No. The stated 68kg load capacity applies to the pair rather than to each individual hanger. Can they be used to hang LED lights?
Yes. Adjustable rope ratchets are particularly useful for LED fixtures because they allow the hanging height to be changed without removing the fixture from its supports. Can I hang a carbon filter with them?
Yes, provided the complete filter and associated suspended equipment remain within the rated load and are attached to suitable structural mounting points. Can they be used with an extraction fan?
Yes. Suitable extraction fans can be suspended using rope ratchets where the weight, mounting arrangement and supporting structure are appropriate. How do I raise equipment using a rope ratchet?
Once the equipment is securely attached, pull the free end of the rope through the ratchet. The mechanism automatically holds the rope as the equipment is raised. How do I lower the equipment?
Support the suspended load and carefully operate the ratchet's release mechanism, allowing the rope to feed back through gradually. With a pair, lower each side progressively to keep the equipment balanced. Are rope ratchets better than fixed chains for adjustable lighting?
For equipment that needs frequent height adjustment, rope ratchets are considerably more convenient because the position can be altered without moving hooks between individual chain links. Should I inspect the ratchets after installation?
Yes. Periodically inspect the rope, clips, ratchet mechanism and mounting points for wear or damage, particularly where equipment remains suspended for long periods. Can I use one ratchet on its own?
The product is supplied and rated as a pair. For equipment with two suspension points, using both ratchets distributes the load and allows the equipment to be levelled correctly. How many packs are in an outer box?
There are 100 twin packs per outer box.
£5.85
Unit price per£5.85
Unit price perThis 24 Hour Digital Plug Timer provides simple automatic control of compatible mains-powered equipment from a standard UK socket. The digital display and programmable switching function allow connected equipment to be turned on and off automatically, removing the need for daily manual switching.
A useful accessory for lighting, fans, pumps and other suitable electrical equipment, the timer plugs directly into a UK wall socket with the appliance then connected to the timer's front socket.
Digital programming provides greater flexibility than a basic mechanical segment timer and is particularly useful where equipment needs to follow a consistent daily operating schedule.
Why choose a 24 Hour Digital Plug Timer?
Automatic control for everyday electrical equipment
Plug-in timers are a simple way to automate equipment that only needs to receive power during predetermined periods. Once programmed, the timer controls the electrical supply to the connected appliance automatically.
This can be useful for suitable lighting, circulation fans, pumps and other equipment where a repeatable operating schedule is required.
Always check the electrical requirements and switching characteristics of the equipment being connected. High-inrush equipment and HID lighting systems can place considerably greater demands on a timer during start-up than their normal running wattage suggests.
Digital programming
The LCD display makes it easy to view the timer's clock and programming settings. Dedicated control buttons are positioned beneath the display for setting and adjusting the required switching programme.
Compared with a traditional mechanical timer, a digital timer removes the need to set physical segments around a dial and provides a clear numerical display when checking the programmed time.
Useful for lighting, ventilation & irrigation schedules
Maintaining consistent operating periods is important across many horticultural applications. A plug-in timer can automate suitable lighting periods, ventilation schedules or irrigation equipment without somebody having to switch the appliance manually each day.
For pumps and other irrigation equipment, make sure the connected device is suitable for timer-controlled operation and that the timer itself is kept away from water and excessive moisture.
Choosing the correct timer for your equipment
The electrical load should always be checked before connecting equipment to a plug-in timer. Do not assume that an appliance is suitable simply because its normal running wattage appears low.
In particular, HID lighting ballasts and some motors can produce a high start-up or inrush current. Where a high-load lighting system is being controlled, use a suitably rated contactor or dedicated lighting controller rather than placing an unsuitable load directly through a general-purpose timer.
The timer should be used in a suitable dry environment and must not be overloaded. Always follow the electrical ratings marked on the individual timer supplied.
24 Hour Digital Timer product details
| Product type | Digital plug-in timer |
|---|---|
| Timer format | 24 hour digital timer |
| Display | LCD digital display |
| Socket format | UK 3-pin socket |
| Control | Push-button digital programming |
| Installation | Plug-in |
| Suitable for | Compatible mains-powered equipment requiring automatic timed switching |
| Typical applications | Suitable lighting, fans, pumps, circulation equipment & other compatible electrical devices |
| Colour | White |
| Outer case quantity | 50 units |
24 Hour Digital Plug Timer FAQs
What does a digital plug timer do?
It automatically switches the electrical supply to compatible connected equipment according to the schedule programmed into the timer. Is this a UK plug timer?
Yes. The timer shown uses a standard UK 3-pin socket format for compatible UK mains equipment. Can I use this timer for lighting?
It can be used with suitable lighting equipment provided the electrical and switching load is within the timer's stated rating. High-inrush HID lighting may require a separate contactor or dedicated lighting controller. Can I use the timer for a fan?
It can be used with compatible fans where the electrical load and start-up characteristics fall within the timer's rating. Check the specifications of both the fan and timer before use. Can a digital timer control an irrigation pump?
Potentially, provided the pump is designed for timer-controlled operation and its electrical requirements are suitable. The timer itself should be kept in an appropriate dry location away from water. Why choose a digital timer instead of a mechanical timer?
A digital timer uses an LCD display and push-button programming rather than physical dial segments, making it convenient where a clearly displayed programmed schedule is preferred. Can I plug a 600W HID ballast directly into this timer?
Do not judge suitability from the 600W running figure alone. HID ballasts can create a substantial start-up current, so a suitably rated contactor or dedicated lighting controller may be required. Always check the timer and ballast specifications before connection. Can this timer be used outdoors?
It should not be assumed to be weatherproof. Unless the individual unit is specifically marked with an appropriate environmental rating, use it only in a suitable dry location. Does it have a manual control?
The timer shown includes a manual control button, allowing the operating mode to be changed directly from the unit when required. How many timers are in an outer box?
The outer case quantity for this product is 50 timers. Individual units can still be sold separately unless otherwise stated.
The Loadstar Pro 600W Dual Spectrum Lamp is a high-pressure sodium (HPS) grow lamp designed to provide useful light for both vegetative growth and flowering from a single 600W lamp. Its dual spectrum output combines the predominantly red/orange output associated with HPS lighting with additional blue-spectrum light, allowing growers to use one lamp throughout the crop cycle.
Designed as a cost-effective replacement lamp for compatible 600W HID lighting systems, the Loadstar Pro uses a standard E40 screw fitting and is intended to operate with a suitable 600W ballast and reflector.
Dual spectrum technology makes the lamp particularly convenient for growers who want to avoid changing between separate vegetative and flowering lamps. It can remain in the lighting system as plants move from vegetative development into flowering and fruiting.
Why choose the Loadstar Pro 600W Dual Spectrum Lamp?
Dual spectrum lighting for vegetative growth & flowering
Traditional HPS lamps produce a spectrum heavily weighted towards the warmer red and orange wavelengths commonly associated with flowering. Dual spectrum HPS lamps modify this output by introducing additional blue-spectrum light.
This broader output makes the Loadstar Pro suitable for vegetative growth as well as flowering, providing growers with a straightforward full-cycle lighting option without having to change between separate metal halide and HPS lamps.
The lamp remains particularly well suited to flowering applications while the additional blue component makes it more versatile for earlier stages of established plant growth.
Proven 600W HPS technology
High-pressure sodium lighting has been widely used in controlled-environment horticulture for many years. A 600W HPS system produces intense light from a relatively compact lamp and can be paired with a suitable reflector to distribute that light across the crop area.
HID lamps generate considerable heat during operation. Appropriate ventilation, reflector positioning and plant-to-lamp distance are therefore important parts of any 600W HPS installation.
E40 fitting for compatible 600W lighting systems
The Loadstar Pro 600W Dual Spectrum Lamp uses an E40 screw base, the common large-format lamp fitting used across many single-ended horticultural HID reflectors.
The lamp requires a compatible 600W HPS ballast. The ballast regulates the electrical supply required to start and operate the lamp and should always be correctly matched to the lamp wattage and type.
Before replacing an existing lamp, isolate the lighting system from the mains supply and allow the old lamp and reflector to cool completely.
Ideal as a replacement 600W grow lamp
HID lamps gradually lose light output through use even when they continue to illuminate normally. Replacing ageing lamps can therefore be an important part of maintaining the performance of an existing HID lighting installation.
The Loadstar Pro provides a straightforward replacement option for suitable 600W HPS systems, particularly where a dual spectrum lamp is preferred for both vegetative and flowering use.
Loadstar Pro 600W Dual Spectrum Lamp product details
| Brand | Loadstar |
|---|---|
| Range | Loadstar Pro |
| Product type | Dual spectrum HPS grow lamp |
| Power | 600W |
| Lamp technology | High Pressure Sodium (HPS) |
| Spectrum | Dual spectrum |
| Lamp fitting | E40 screw base |
| Growth stages | Vegetative growth & flowering |
| Ballast required | Yes - compatible 600W HPS ballast |
| Reflector required | Suitable E40 HID reflector / lamp holder |
| Suitable for | Full-cycle plant lighting & replacement in compatible 600W HPS systems |
Loadstar Pro 600W Dual Spectrum Lamp FAQs
Is the Loadstar Pro 600W an HPS lamp?
Yes. It is a 600W high-pressure sodium grow lamp with a dual spectrum output. What does dual spectrum mean?
Dual spectrum HPS lamps supplement the predominantly warm red/orange output of conventional HPS lighting with additional blue-spectrum light, making the lamp more versatile across different plant growth stages. Can I use the Loadstar 600W lamp for vegetative growth?
Yes. The dual spectrum output is designed to make the lamp suitable for vegetative growth as well as flowering. Can I use the same lamp for flowering?
Yes. Flowering is a core application for HPS lighting, and the Loadstar Pro can remain in use as plants move from vegetative growth into the flowering stage. What fitting does the Loadstar Pro 600W use?
It uses an E40 screw fitting, commonly found on single-ended HID horticultural reflectors and lamp holders. Does this lamp need a ballast?
Yes. The lamp must be operated with a suitable ballast designed for a 600W HPS lamp. It must not be connected directly to the mains supply. Can I fit it into an LED fixture?
No. This is a replaceable HID lamp intended for a compatible 600W HPS ballast and E40 reflector system. It is not an LED replacement component. Does a 600W HPS lamp produce much heat?
Yes. HID lighting converts a significant amount of electrical energy into heat as well as light, so suitable ventilation and safe clearance around the lamp and reflector are important. Should I touch the glass when fitting the lamp?
It is good practice to handle HID lamps carefully and avoid unnecessary contact with the glass. Always install or replace the lamp with the lighting system isolated from the mains and completely cool. Is this a good replacement for an old 600W dual spectrum bulb?
It is suitable as a replacement where the existing lighting system uses a compatible 600W HPS ballast and E40 lamp holder. Always check the ballast and reflector specifications before installation.
£5.00
Unit price per£5.00
Unit price perThe Lumatek UV LED Daisy Chain Cable 1.5m is the dedicated linking cable for connecting multiple Lumatek 30W UV Supplemental LED Bars together in series. It allows additional UV bars to receive power through the preceding fixture, creating a cleaner multi-bar installation without requiring an individual mains power cable for every UV bar.
Lumatek's 30W UV Supplemental LED Bar features both an input and output connection specifically to support daisy-chain operation. The first UV bar is connected to the mains using the separately available Lumatek UV power cable, with additional bars then linked using these 1.5m daisy chain cables.
Lumatek specifies a maximum daisy-chain capacity of 30 x 30W UV Supplemental LED Bars from one power source, making the cable suitable for anything from a simple two-bar installation through to larger professional supplemental lighting layouts.
Why choose the Lumatek UV Daisy Chain Cable?
How the Lumatek UV daisy-chain system works
A Lumatek 30W UV Supplemental LED Bar can either receive power directly through its input connection or receive power from the output of another UV bar in the chain.
The first fixture requires the appropriate Lumatek UV LED Bar power cable. A 1.5m daisy chain cable is then connected from the power output of the first UV bar to the power input of the second. Further bars can be added using an additional daisy chain cable between each fixture.
This means a two-bar arrangement requires one daisy chain cable, a three-bar arrangement requires two, and so on. The power cable and daisy chain cables are separate accessories.
Designed for the Lumatek 30W UV Supplemental LED Bar
This 1.5m cable is specifically intended for Lumatek's 30W UV Supplemental LED Light Bar. The UV fixture incorporates dedicated input and output sockets that allow several bars to be connected together in series.
Lumatek specifies a maximum of 30 compatible UV bars in a single daisy-chain arrangement. Always stay within the manufacturer's stated maximum and use the correct Lumatek power and connection cables for the system.
Simple connection between UV bars
Before connecting the fixtures, ensure that mains power is switched off. Align the connector on the daisy chain cable with the output connection of the first UV bar and push it into place until securely locked. Connect the opposite end to the input of the next UV bar.
Repeat the process for any additional fixtures, using one daisy chain cable for each additional UV bar in the series.
Lumatek specifically advises that UV fixtures should not be connected or disconnected while under load. Always switch off the mains supply before adding, removing or disconnecting fixtures or cables.
How many daisy chain cables do I need?
| Number of UV bars | Daisy chain cables required |
|---|---|
| 1 UV bar | None - use the appropriate Lumatek power cable |
| 2 UV bars | 1 daisy chain cable |
| 3 UV bars | 2 daisy chain cables |
| 4 UV bars | 3 daisy chain cables |
| 5 UV bars | 4 daisy chain cables |
As a simple rule, a daisy-chained installation requires one fewer daisy chain cable than the number of UV bars. The first bar also requires the appropriate Lumatek power cable to connect the chain to its power source.
Lumatek UV LED Daisy Chain Cable product details
| Brand | Lumatek |
|---|---|
| Product type | UV LED bar daisy chain / link cable |
| Cable length | 1.5m |
| Primary compatibility | Lumatek 30W UV Supplemental LED Light Bar |
| Function | Connects compatible Lumatek UV LED bars together in series |
| Connection | UV bar output to next UV bar input |
| Maximum UV daisy chain | Up to 30 compatible 30W UV bars from one power source |
| Power cable | Required for the first UV bar and sold separately |
| Installation | Connect and disconnect only with mains power switched off |
Lumatek UV LED Daisy Chain Cable FAQs
What is the Lumatek 1.5m UV Daisy Chain Cable used for?
It is used to connect compatible Lumatek 30W UV Supplemental LED Bars together in series, linking the output of one UV fixture to the input of the next. How long is the cable?
The Lumatek UV Daisy Chain Cable is 1.5 metres long. Can I connect two Lumatek UV bars together?
Yes. Connect the first UV bar to the appropriate power cable and use one 1.5m daisy chain cable to link the first bar to the second. How many Lumatek UV bars can be daisy chained?
Lumatek specifies a maximum of 30 x 30W UV Supplemental LED Bars in a daisy-chain arrangement from one power source. Does this cable replace the Lumatek UV power cable?
No. The first UV bar still requires the appropriate Lumatek power cable. The 1.5m daisy chain cable is then used to connect each additional UV bar to the preceding fixture. How many cables do I need for three UV bars?
Three UV bars require two daisy chain cables, plus the appropriate power cable for the first bar. Is the 1.5m daisy chain cable supplied with the UV bar?
No. Lumatek lists the UV bar power cable and the 1.5m UV daisy chain cable as separate accessories. Can I connect or disconnect the cable while the UV bars are switched on?
No. Lumatek instructs users not to connect or disconnect the UV fixtures under load. Switch off the mains power before connecting, disconnecting or altering the daisy chain. Is this a Lumatek-specific accessory?
Yes. It is designed for the connection system used by compatible Lumatek supplemental UV LED bars. Compatibility should be confirmed before attempting to use it with any other equipment.
£19.50
Unit price per£19.50
Unit price perThe Loadstar 4 Way Timer Contactor is a heavy-duty lighting controller designed to safely automate the switching of up to 4 x 600W lighting systems. Combining a built-in segmental timer with a heavy-duty contactor, four individually switchable output sockets and a robust metal enclosure, it provides a convenient central control point for multi-light installations.
High-powered lighting places significantly greater switching demands on a timer than ordinary low-load electrical equipment. A contactor separates the timer from the main switching load, allowing the timer to control the contactor rather than carrying the full lighting load itself.
This makes the Loadstar 4 Way Timer Contactor particularly useful for installations where several compatible lighting systems need to switch on and off together according to a repeatable daily schedule.
Why choose the Loadstar 4 Way Timer Contactor?
Why use a contactor for high-powered lighting?
The important difference between a standard timer and a timer contactor is the way the electrical load is switched.
High-powered lighting equipment can produce a significant electrical demand during start-up. Repeatedly switching this type of load directly through a standard timer can place considerable stress on the timer's internal switching contacts.
A contactor is designed to handle the main switching operation. The timer controls the contactor, while the contactor switches the connected lighting load. This arrangement is particularly useful when several lighting systems need to operate simultaneously.
Built-in segmental timer
The integrated segmental timer allows the connected lighting schedule to be automated directly from the Loadstar controller. Once the required on and off periods have been set, the timer repeats the programme each day.
This provides a simple mechanical approach to lighting automation without relying on a separate external timer for the four connected outputs.
The analogue format also makes the programmed lighting period easy to see at a glance, which can be useful when checking or adjusting a lighting schedule.
Four-way lighting control
The Loadstar controller provides four output sockets, allowing up to four compatible lighting systems to be controlled from the same timer programme.
Loadstar specifies the 4 Way Timer Contactor for handling up to 4 x 600W lights. This makes it a convenient option for installations where several lights need to follow the same operating schedule.
Each socket is switchable and incorporates a power indicator, providing straightforward local control and visual confirmation at the controller.
Robust wall-mountable design
The controller is housed in a robust metal enclosure and incorporates wall mounting hooks. Mounting the controller securely in a suitable location helps keep the electrical installation organised and keeps the unit away from areas where it could be knocked or exposed to water.
As with all mains-powered lighting equipment, the controller should be installed and operated in accordance with its supplied instructions and within the specified electrical limits. Keep electrical connections dry and do not exceed the stated lighting capacity.
Loadstar 4 Way Timer Contactor product details
| Brand | Loadstar |
|---|---|
| Product type | Timer contactor / lighting controller |
| Number of output sockets | 4 |
| Lighting capacity | Up to 4 x 600W lights |
| Timer | Built-in segmental timer |
| Socket control | Individually switchable outputs |
| Power indication | Socket power indicators |
| Enclosure | Robust metal housing |
| Mounting | Wall mounting hooks |
| Primary application | Automatic switching of compatible high-powered lighting systems |
| Warranty | 2 years |
| Outer case quantity | 8 units |
Loadstar 4 Way Timer Contactor FAQs
How many lights can the Loadstar 4 Way Timer Contactor control?
The Loadstar 4 Way model is specified to control up to 4 x 600W lighting systems. Does the Loadstar 4 Way Contactor have a timer built in?
Yes. This model incorporates a segmental timer, allowing the connected lights to be automatically switched according to the programmed daily schedule. Why do I need a contactor instead of an ordinary timer?
A contactor is designed to perform the main switching operation for higher electrical loads. The timer controls the contactor rather than directly switching the full lighting load, reducing the switching demand placed on the timer itself. Do all four sockets follow the same timer programme?
Yes. The unit is designed to provide centralised timed control for lighting systems that need to follow the same operating schedule. Can the individual sockets be switched?
Yes. The Loadstar unit features switchable output sockets, allowing individual outputs to be controlled locally at the contactor. Can the Loadstar 4 Way Timer Contactor be wall mounted?
Yes. Wall mounting hooks are incorporated into the unit, allowing it to be securely positioned in a suitable location. Does it have a plastic or metal enclosure?
The Loadstar 4 Way Timer Contactor uses a robust metal housing designed to protect the internal switching components. Can I exceed four 600W lights if the sockets are available?
No. The stated capacity of the 4 Way model is up to four 600W lights. Do not exceed the manufacturer's specified electrical loading, regardless of the number of available sockets. Where should the timer contactor be installed?
Install the controller securely in a suitable dry location, away from irrigation, standing water and excessive moisture, and follow the supplied electrical and installation instructions. How many Loadstar 4 Way Timer Contactors are in an outer case?
The outer case quantity for this product is 8 units.